[Icc-avr] Port ASM from GCC to ICC

[sbissonnette at microsyl.com]

(Second try)
Hi,

    I have a problem,  I had never work in ASM and I have a small piece of
code to port from GCC to ICC
Could someone help me?

Thanks
Sylvain Bissonnette

#include <io2313.h>


.section .text

;******************************************************************************
; data tables
;******************************************************************************

; force table to begin at 256 byte boundary

.org 0x100

sine: ; 256 step sinewave table
.byte0x80,0x83,0x86,0x89,0x8c,0x8f,0x92,0x95,0x98,0x9c,0x9f,0xa2,0xa5,0xa8,0xab,0xae
.byte
0xb0,0xb3,0xb6,0xb9,0xbc,0xbf,0xc1,0xc4,0xc7,0xc9,0xcc,0xce,0xd1,0xd3,0xd5,0xd8
.byte0xda,0xdc,0xde,0xe0,0xe2,0xe4,0xe6,0xe8,0xea,0xec,0xed,0xef,0xf0,0xf2,0xf3,0xf5
.byte
0xf6,0xf7,0xf8,0xf9,0xfa,0xfb,0xfc,0xfc,0xfd,0xfe,0xfe,0xff,0xff,0xff,0xff,0xff
.byte0xff,0xff,0xff,0xff,0xff,0xff,0xfe,0xfe,0xfd,0xfc,0xfc,0xfb,0xfa,0xf9,0xf8,0xf7
.byte
0xf6,0xf5,0xf3,0xf2,0xf0,0xef,0xed,0xec,0xea,0xe8,0xe6,0xe4,0xe2,0xe0,0xde,0xdc
.byte0xda,0xd8,0xd5,0xd3,0xd1,0xce,0xcc,0xc9,0xc7,0xc4,0xc1,0xbf,0xbc,0xb9,0xb6,0xb3
.byte
0xb0,0xae,0xab,0xa8,0xa5,0xa2,0x9f,0x9c,0x98,0x95,0x92,0x8f,0x8c,0x89,0x86,0x83
.byte0x80,0x7c,0x79,0x76,0x73,0x70,0x6d,0x6a,0x67,0x63,0x60,0x5d,0x5a,0x57,0x54,0x51
.byte
0x4f,0x4c,0x49,0x46,0x43,0x40,0x3e,0x3b,0x38,0x36,0x33,0x31,0x2e,0x2c,0x2a,0x27
.byte0x25,0x23,0x21,0x1f,0x1d,0x1b,0x19,0x17,0x15,0x13,0x12,0x10,0x0f,0x0d,0x0c,0x0a
.byte
0x09,0x08,0x07,0x06,0x05,0x04,0x03,0x03,0x02,0x01,0x01,0x00,0x00,0x00,0x00,0x00
.byte0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x02,0x03,0x03,0x04,0x05,0x06,0x07,0x08
.byte
0x09,0x0a,0x0c,0x0d,0x0f,0x10,0x12,0x13,0x15,0x17,0x19,0x1b,0x1d,0x1f,0x21,0x23
.byte0x25,0x27,0x2a,0x2c,0x2e,0x31,0x33,0x36,0x38,0x3b,0x3e,0x40,0x43,0x46,0x49,0x4c
.byte
0x4f,0x51,0x54,0x57,0x5a,0x5d,0x60,0x63,0x67,0x6a,0x6d,0x70,0x73,0x76,0x79,0x7c

;******************************************************************************
; code
;******************************************************************************


GO:
 ; set sinewave output as default

ldi r31,hi8(sine) ; setup Z pointer hi
ldi r30,lo8(sine) ; setup Z pointer lo

; clear accumulator

ldi r29,0x00 ; clear accumulator
ldi r28,0x00 ; clear accumulator

; setup adder registers ldi r24,0x55 ; setup adder value
ldi r25,0x35 ; to 1 kHz
ldi r26,0x00 ;

LOOP1:
add r28,r24 ; 1
adc r29,r25 ; 1
adc r30,r26 ; 1
lpm ; 3
out PORTB,r0 ; 1
rjmp LOOP1 ; 2 => 9 cycles